BotronikS

Arduino ready-made codes (with some hardware) for PC:

No need to know Arduino programming! Just connect peripherals (according to the scheme) and connect to PC!

MAK101: 4x Outputs + 4x Temperature sensors DS18B20
Scheme:	SET1: Nano+...	Termite test:	DS18B20	BScadaID_8V8O_Try6h
Power: PC-USB Outputs: 0/5V max 30mA - Sensors: 4xDS18B20 (-50.0/+120.0C)
TEXT command set (ASCII characters + ENTER) - Baud 9600,8 Data bits, None Parity,1 Stop Bit (free: Termite)
AT, ATI : returns OK , returns code name
OxH , OxL : Set output x (1-4) to H (5V) or L (0V) level (exasmple: O1H)
V0x - returns sensor temperature in C (x=1-4) (exsample: V01)

Note: SET1 has build in resistors for DS18B20
HexCodeTry (Trial code - Limited to 1000 receiving commands - then need a reset). For upload use a free XLoader
BScada: BScada16out (read how, install and try first) - BScada8V8Od_Try6h

Offer(s):
MAK101-SET1: Programmed and tested SET1 with USB cable - without additional equipment: Price: €40
MAK101-SET1A: SET1+4x sensor DS18B20: Price: €80

Recommended project equipment:
For outputs: Link1 - Link2 - Link3
For sensors: Link1 - Link2

MAK101A: 8x Outputs + 4x Temperature sensors DS18B20

Scheme - TermiteTest - HexCodeTry (Trial code - Limited to 1000 receiving commands - then need a reset)

MAK101A-SET1: Programmed (no limited code) and tested SET1 with USB cable - without additional equipment: Price: €40

MAK102: 4x Outputs + 4x Temperature & Humidity sensors DHT22/AM2302
Scheme:	SET1: Nano+...	Termite test:	AM2302	BScada8V8Od_Try6h
Power: PC-USB Outputs: 0/5V max 30mA - Sensors: 4xDHT22/AM2302 (-40/+80C 0-100%RH)
TEXT command set (ASCII characters + ENTER) - Baud 9600,8 Data bits, None Parity,1 Stop Bit (free: Termite)
AT, ATI : returns OK , returns code name
OxH , OxL : Set output x (1-4) to H (5V) or L (0V) level (exasmple: O1H)
V0x - returns sensors values (x=1-8) (exsample: V01 (sensor1 Temp.) V02 (sensor1 Hum.))

Note: V01/V02=Sensor1 Temp/Hum, V03/V04=Sensor2 Temp/Hum ----- V07/V08=Sensor4 Temp/Hum
Note: SET1 has build in resistors for sensors
HexCodeTry (Trial code - Limited to 1000 receiving commands - then need a reset). For upload use a free XLoader
BScada: BScada16out (read how, install and try first) - BScada8V8Od_Try6h

Offer(s):
MAK102-SET1: Programmed and tested SET1 with USB cable - without additional equipment: Price: €40
MAK102-SET1A: SET1+4x sensor AM2302: Price: €90

Recommended project equipment:
For outputs: Link1 - Link2 - Link3
For sensors: Link1 - Link2

MAK102A: 8x Outputs + 4x Temperature & Humidity sensors DHT22/AM2302

Scheme - TermiteTest - HexCodeTry (Trial code - Limited to 1000 receiving commands - then need a reset)

MAK102A-SET1: Programmed (no limited code) and tested SET1 with USB cable - without additional equipment: Price: €40

MAK103: 4x Outputs + 1x Temperature K Type Thermocouple MAX6675
Scheme:	SET1	Termite test:	MAX6675
Power: PC-USB Outputs: 0/5V max 30mA - Sensor(s): MAX6675 temperature module (0-400/500/600/1000 C)
TEXT command set (ASCII characters + ENTER) - Baud 9600,8 Data bits, None Parity,1 Stop Bit (free: Termite)
AT, ATI : returns OK , returns code name
OxH , OxL : Set output x (1-4) to H (5V) or L (0V) level (exasmple: O1H)
V0x - returns sensors values (x=1) (exsample: V01 (sensor1 Temp.))

HexCodeTry (Trial code - Limited to 1000 receiving commands - then need a reset). For upload use a free XLoader
BScada: BScada16out (read how, install and try first) - BScada8V8Od_Try6h

Offer(s):
MAK103-SET1: Programmed and tested SET1 with USB cable - without additional equipment: Price: €40
MAK103-SET1A: SET1+1x sensor MAX6675: Price: €60

Recommended project equipment:
For outputs: Link1 - Link2 - Link3
For sensors: Link1 - Link2 - Link3

MAK110: 4xOut+1xDS18B20+1xDHT22+1xTemperature Thermocouple MAX6675
Scheme:	SET1	Termite test:	DS18B20	AM2302	MAX6675
Power: PC-USB Outputs: 0/5V max 30mA - Sensor(s): 1=DS18B20 2=DHT22/AM2302 3=MAX6675 temperature module
TEXT command set (ASCII characters + ENTER) - Baud 9600,8 Data bits, None Parity,1 Stop Bit (free: Termite)
AT, ATI : returns OK , returns code name
OxH , OxL : Set output x (1-4) to H (5V) or L (0V) level (exasmple: O1H)
V0x - returns sensors values (x=1) (exsample: V01 (sensor1 Temp.))

Note: V01=Sensor1(Temp) V02/V03=Sensor2(Temp/Hum) V04=Sensor3(Temp)
HexCodeTry (Trial code - Limited to 1000 receiving commands - then need a reset). For upload use a free XLoader
BScada: BScada16out (read how, install and try first) - BScada8V8Od_Try6h

Offer(s):
MAK110-SET1: Programmed and tested SET1 with USB cable - without additional equipment: Price: €40
MAK110-SET1A: SET1+1xDS18B20+1xAM2305+1xMAX6675: Price: €80

Recommended project equipment:
For outputs: Link1 - Link2 - Link3
For sensors: Link1 - Link2 - Link3